Electrical advice for Crewe homes

Why does my fuse box keep tripping?

When a switch in the fuse box trips, treat it as an alarm going off. Something on the circuit drew too much current, or let current leak where it should not go, and the switch cut the power to protect you and the cables.

Reset it once and it may never happen again. When it keeps happening, the pattern tells you a good deal about the cause.

Which switch has tripped?

Open the cupboard and look, without touching anything but the switches. A modern board has three kinds.

The small switches, one for each circuit. These are circuit breakers. Each looks after one set of sockets or lights. One of these tripping alone usually means that circuit was overloaded, or has a dead short on it.

The wider switch with a button marked Test or T. This is the RCD. It trips when current leaks to earth, which is what happens with damp, a damaged cable or a failing appliance. On many boards one RCD covers several circuits, so half the house goes off together.

The main switch. This turns everything off. It does not trip of its own accord.

An older board with pull-out fuses does not trip at all. A fuse blows and stays blown. If that keeps happening, the advice in this article still applies, and the board itself is due for replacement.

Cause one: too much on one circuit

The kettle, the toaster and the microwave are all on together, in a kitchen wired when kitchens held far fewer machines. The breaker for the kitchen sockets trips, and it goes back on happily once something is switched off.

The clue is timing. It happens when several heavy appliances run at once and never otherwise. Spreading the load helps for now. The lasting cure is an extra circuit, which an electrician can add if the board has room.

Cause two: an appliance on its way out

Heating elements are the usual offenders. Kettles, ovens, washing machines, dishwashers, immersion heaters and tumble dryers all have one. As an element ages, a little current begins to leak from it, and the RCD picks it up.

The clue is that the trip follows one machine. It goes when the oven has been on for ten minutes, or part way through a wash. Leave that appliance unplugged for a few days. If the tripping stops, you have found it, and it needs an appliance repairer or a replacement, not an electrician.

Cause three: damp

Water carries current to places it should never reach. An outside light with a perished seal, a garden socket, a cable through a wet wall or a leak from the bathroom above a ceiling light can all trip an RCD.

The clue is the weather. It trips in heavy rain or a day or so after, and behaves in a dry spell. In Crewe's older terraces, look at the outside light by the back door and at anything fixed to a wall that takes the weather.

Cause four: a damaged cable or a worn fitting

A picture nail can go through a cable, and a floorboard can be screwed down on top of one. A connection in the back of a socket can work loose after decades of plugs going in and out. Insulation goes hard and cracks with age.

The clue is that there is no pattern you can find, or that it began just after some work on the house. This is the cause that most needs a professional, because the damage is hidden and can be heating up between trips.

Safe checks you can make yourself

There is one useful test that involves nothing more than plugs and switches.

  1. Note which switch has tripped and which sockets or lights have gone off.
  2. Unplug everything on those sockets. Everything, including the things you never think about, such as the fridge and the boiler.
  3. Push the switch back up. If it stays up, plug things back in one at a time, a few minutes apart.
  4. If it trips as one item goes back in, leave that item unplugged and tell the electrician or a repairer.
  5. If it trips with nothing plugged in at all, the fault is in the wiring. Leave the switch down.

That is as far as a householder should go. Do not open sockets, switches, light fittings or the fuse box. Do not hold a switch up or tape it. And if there is any smell of burning, heat or scorching, stop and treat it as urgent: see emergency electrician in Crewe.

When to stop testing and ask

  • The switch will not reset with everything unplugged
  • It trips with no pattern you can find
  • More than one switch has started tripping
  • Anything is warm, marked or smells odd
  • It is the lighting circuit, where there is nothing to unplug
  • You have an old board with fuses that keep blowing

An electrician will test each circuit with instruments and narrow the fault down step by step. Our page on electrical fault finding in Crewe describes how, and what to note down beforehand.

Common questions

Is it dangerous if my fuse box keeps tripping?

The tripping itself is the safety system working. The danger lies in whatever is causing it, and in the temptation to keep resetting the switch. A circuit that trips again and again should be left off until the cause is found.

Why does the trip switch go when a light bulb blows?

When an old-style bulb fails, there can be a brief surge as the filament breaks, and a sensitive breaker reacts to it. Reset the switch and change the bulb. If it happens with no bulb failing, something else is going on.

Can a fuse box wear out and trip for no reason?

It can, though it is less common than a real fault. Breakers and RCDs are mechanical and do weaken with age. An electrician can test the device itself. If the board is decades old, a modern replacement may be the sensible answer.

Tired of walking to the cupboard under the stairs?

A switch that trips every week is telling you about a fault that is still there the other six days. Damp creeps further, worn connections get hotter and old cable gets no better. Having it traced is the only way to make it stop for good.

Say which switch trips and when, and where in Crewe you are. The call back is free.

Ask a Crewe electrician for a quote

Four short boxes. A minute at most.

By sending this form you agree to your details being shared with a local electrician so they can contact you. See our privacy notice.

Get a free quote